Either apply Waterproof Finish or Ultra-Mix by Peletico (solution 1) or apply, using a trowel, one coat of Exterior Pelemura and then two coats of Fine Exterior Pelemura crosswise (horizontal and vertical) to achieve a smooth surface (solution 2).
Apply primer EcoPrimer by Peletico (water based), or Masonry Conditioner by Sherwin-Williams® (solvent based).
Apply 3 coats of Loxon® Exterior Masonry Elastomeric coating by Sherwin-Williams® , or 3 coats of Perlotex Matt fine textured paint by Peletico.
Apply, using a trowel, two crosswise (horizontal and vertical) coats of Pelemura by Peletico.
Apply primer/stabilizer EcoPrimer by Peletico.
Apply 3 coats of Maxicote emulsion paint by Peletico or 3 coats of ProMar® 200 emulsion paint by Sherwin-Williams® .
First sand the wooden surface, then clean and paint with water based Wood Primer by Peletico.
Clean the galvanised steel surface from dirt, dust, grease and oil stains.
Apply water based Grey Metal Primer, or Red Oxide Metal Primer by Peletico.
Clean the soot from the surfaces well.
Apply primer Alkali Resisting Primer by Peletico, or Preprite200 by Sherwin-Williams® .
Apply 3 coats of interior emulsion paint, by Peletico or Sherwin-Williams®® .
Sand the surface and then clean from possible dust, dirt etc.
Apply EcoPrimer by Peletico, Masonry Conditioner® or Preprite® 200 by Sherwin-Williams® .
Clean the metal surface from dirt, dust, oil stains and rust.
Apply 2-3 coats of No Rust® Hammered Metal Paint by Ronseal® .
Clean the metal surface from dirt, dust, oil stains and rust.
Scrape off peeling or cracked paint and sand to a sound surface.
Apply one coat of water based Grey Metal Primer or Red Oxide Primer by Peletico.
Apply one coat of water based Undercoat by Peletico, or one coat of water based ProMar® 200 Undercoat by Sherwin-Williams® .
Apply two coats of Gloss Finish or Satin Finish by Peletico, or two coats of ProMar® 200 Satin or Gloss Enamel by Sherwin-Williams® .
Recommendations:
Maxicote by Peletico.
Trimul by Peletico.
ProMar® 200 by Sherwin-Williams® .
ProMar® 200 Interior Semi-Gloss by Sherwin-Williams® .
ProMar® 700 by Sherwin-Williams® .
Sens eco Premium by Peletico available in colours P101, P104, P110 & P201.
Sens eco Trade by Peletico available in colours P101 & P104.
We recommend Loxon® Exterior Masonry Elastomeric coating by Sherwin-Williams® in various colour options (refer to Sherwin-Williams® fan deck).
We recommend Perlotex Matt by Peletico in various colour options (refer to Peletico’s Perlotex Matt colour chart).
Coat all the drywall joints with Uniplast by Peletico. Apply one coat of Uniplast to the entire drywall surface with a toothed trowel and then apply fiber mesh on top of the Uniplast coat. On the next day, cover up the entire fiber mesh with Uniplast. When the material is dry, apply a final coat of Ultra-Mix by Peletico and then apply any exterior coating like Loxon® and A-100® by Sherwin-Williams® or Perlotex Matt by Peletico.
If there are hairline cracks trowel them with Pelemura, Pelefilla or Spatulin Acrylic (water based). If the cracks are big, expand the crack on both sides by 5cm and apply Pelefix.
Before Pelefix dries up, apply Uniplast and then fiber mesh. Next day, cover up the mesh with Uniplast.
Apply Pelemura or Fine Exterior Pelemura with a trowel and then apply any interior emulsion paint by Peletico or Sherwin-Williams® .
If there are hairline cracks on the exterior, trowel them with Exterior Pelemura. If the cracks are big, expand the crack on both sides by 5cm and apply Pelefix.
Before Pelefix dries up, apply Uniplast and then fiber mesh. Next day, cover up the mesh with Uniplast.
Apply Fine Exterior Pelemura with a trowel and then apply any exterior coating by Peletico or Sherwin-Williams®
Remove all surface contamination, e.g. dirt, dust, grease, oil stains and dampness.
Peeling, cracked or old glossy paint should be scraped off and sanded to a sound surface.
Apply one coat of EcoPrimer by Peletico, Masonry Conditioner® or Preprite® 200 by Sherwin-Williams® .
Apply 2-3 coats of emulsion paint using products by Peletico or Sherwin-Williams®.
Lightly sand the surface. Wherever wood imperfections are present, fill them with Spatulin by Peletico. After it is dry, sand the surface again.
Apply water based Wood Primer by Peletico.
Apply water based Undercoat by Peletico, or ProMar® 200 Undercoat by Sherwin-Williams® .
Apply 2 coats of water based enamel paint, either Gloss or Satin Finish by Peletico, or ProMar® 200 Gloss Enamel or ProMar® 200 Satin Enamel by Sherwin-Williams® .
Remove previous varnish completely by scraping and sanding. Always work in the direction of the wood grain. Any broken edges or surface beginning to flake must be feathered down to a smooth edge.
Old varnish may require removal with paint remover. Only water based removers should be used like Peletico’s Paint and Varnish Remover. Then clean and allow to dry.
Apply 2 coats of Uviten water based varnish by Peletico (refer to Uviten colour chart), 5 year Woodstain® (refer to ® colour chart) or Clear Outdoor Varnish by Ronseal® .
Remove previous varnish completely by scraping and sanding. Always work in the direction of the wood grain. Any broken edges or surface beginning to flake must be feathered down to a smooth edge.
Old varnish may require removal with paint remover. Only water based removers should be used like Peletico’s Paint and Varnish Remover. Then clean and allow to dry.
Apply 2-3 coats of water based Hardwood Furniture Stain by Ronseal® .
Interior: Apply 2 coats of Ronseal® Diamond Hard Floor Varnish Clear Gloss or Satin, or 2 coats 2-Pack Polyutherane Varnish by Peletico.
Exterior: Apply 2 coats of Decking Oil or Decking Stain by Ronseal® .
Clean the substrate and then apply one of the following products:
2 coats of Stonoseal by Peletico (for vertical stone surfaces).
2 coats of Stone & Concrete Sealer by Sherwin-Williams® .
Block Paving Seal by Thompson® .
One Coat Water Seal Ultra by Thompson® (for vertical surfaces).
We advise you to make a preliminary sample before application of the above products, as the appearance of the surfaces may alter.
The recommended thermal insulating plasters are Pelelite Bonding Tricote T2 for interior surfaces, with λ=0.15w/mk, and Thermocem T2 for exterior surfaces, with λ=0.175w/mk.
The interior plaster Pelelite Bonding Tricote T2 does not require a 1st coat cement mortar.
The exterior plaster Thermocem T2 requires a 1st coat cement mortar.
Apply a substrate of Pelelite Bonding Tricote T2 and a final coat of Pelelite Finish, which will yield the results of a wall levelled surface on the interior. The Pelelite Finish can be applied on a Thermocem T2 substrate or on traditional plaster as well.
On the interior, apply Pelelite Bonding Tricote T2 as a substrate and as a finishing plaster coat, Pelelite Finish.
On the exterior, apply a mixture of Pelefix and cement (2L Pelefix every 25kg cement) as the first coat. As a second coat, apply Thermocem T2 and as a third coat apply Thermocem Finish or Ultra-Mix by Peletico.
If the spritz is not painted:
Remove all cracked or peeling texture material and then wash.
When dry, apply one coat of Monocote plaster with Pelefix (½ L Pelefix every 25kg Monocote).
Apply 2 coats of Thermocem Finish, or Ultra-Mix by Peletico.
If the spritz is painted:
Remove all cracked or peeling texture material and then wash
When dry, apply one coat of Uniplast and two coats of Thermocem Finish or Ultra-Mix by Peletico.
We recommend 3 coats of Loxon® , or A-100® by Sherwin-Williams® , or 3 coats of Perlotex Matt fine textured paint by Peletico.
Ultra-Mix is a finishing coat cement plaster. When applied, the total thickness of coating should not exceed 3mm. Therefore, as a thin layer it needs to be coated. If its natural colour is desirable, we recommend application of Stone and Concrete Sealer by Sherwin-Williams® .
It is an inorganic, natural, volcanic mineral that is environmentally friendly. Its characteristics include excellent thermal and sound insulation properties. It has significant advantages compared to polystyrene: it is a natural mineral, resistant to high temperatures, fire retarding, it has a neutral pH and is resistant to fungi and rodent attack. It is used in the construction industry. It has a thermal conductivity around λ=0,40 w/mk. Perlite is also used in roofs and mezzanines of buildings and as an additive in thermally insulating coatings.
When the third coat plaster has been badly made, it has to be sanded and then cleaned. Consequently, Pelefix should be applied, and before it is dry, apply 2 coats of Exterior Pelemura horizontally and vertically. This is done to correct as many defects in the masonry as possible.
In floors with underfloor heating, install ceramic tiles using Pelecrete Flex C2TE-S1 or Pelecrete Ultra C2TE-S2 tile adhesive by Peletico.
For surfaces where the substrate is gypsum based, cement based plasters cannot be applied, whereas, the opposite is feasible.
For swimming pools, we recommend Pelecrete Flex C2TE-S1 or Pelecrete Ultra C2TE-S2 tile adhesive.
We recommend Pelecrete Flex C2TE-S1, or Pelecrete Ultra C2TE-S2.